Flow Control Valves

• • 

  • 2F1C Series Pressure Compensated Flow Control Valves

    2-way flow control valves series 2F1C in size NG 10 and NG16 provide a pressure and viscosity compensated flow. Additionally they avoid unintended initial actuator motion.

• • 

  • 2VS3-06 Restrictor Valve with Reverse Flow Check

    The 2VS3-06 is a Restrictor valve with reverse flow check, mounting interface acc. to ISO 4401, DIN 24340 (CETOP 02). •Meter-in or meter-out flow control •Leak-free closing in one or two service ports •Linear adjustment and positive seat overlap •Desired settings may be locked down •Optionally adjustable by allen key with protective cap, or by […]

• • 

  • CFQ Priority Type Flow Control Valve

    Series CFQ flow controls are priority type flow controls. A constant rate of flow is maintained at the constant flow port regardless of changes in load pressure located downstream. It has an electro-nickeless plated spool and a high-tensile cast iron body.

• • 

  • F Series Throttle Check Valve

    The F series of hydraulic flow control valves permits free flow in one direction and metered flow in the reverse direction. This flow control valve is used in air and oil applications.

• • 

  • F5C Series Proportional Throttle Valves

    Series F5C proportional throttle valves adjust flow in the proportion to the input signal. The combination of the F5C with pressure compensators R5A or R5P serves as a flow control valve, providing load compensated flow.

• • 

  • FCC 10320 Flow Regulator Pressure Compensated Valve

    The valve maintains a constant flow at 3, regardless of pressure variations. Flow reverse passage is free and bypasses the control orifice. To optimize regulation, the way 2 must have minimum 5 bar of back pressure.

• • 

  • FCC 12320 Flow Regulator Pressure Compensated Valve

    The valve maintains a constant flow from port 1 to 3, regardless of pressure variations. Flow reverse passage is free and bypasses the control orifice. To optimize regulation, the way 2 must have minimum 5 bar of back pressure.

• • 

  • FCM 08220 Needle Valve

    The valve allows the regulation of flow passage with a screw.

• • 

  • FCM 10220 Flow Regulator Valve, 2 Ways, Pressure Compensated

    The valve allows the regulation of flow passage with a screw.

• • 

  • FCM 12220 Flow Regulator Valve, 2 Ways, Pressure Compensated

    The valve allows the regulation of flow passage with a screw.

• • 

  • FCMB Flow Regulator (For Terv)

    The valve allows the regulation of flow passage with a screw.

• • 

  • FCU 08220 Unidirectional Flow Control Valve

    The valve allows the regulation of flow passage from 2 to 1 with a screw. In the opposite direction, flow is free.

• • 

  • FCU 10220 Unidirectional Flow Control Valve

    The valve allows the regulation of flow passage from 2 to 1 with a screw. In the opposite direction, flow is free.

• • 

  • FSC 10220 Flow Regulator Valve, 2 Ways, Pressure Compensated

    The valve maintains a constant flow from port 1 to 2, regardless of load pressure variations. The flow depends upon control orifice and pressure drop from 1 to 2 (generated by spring). Flow passage from 2 to 1 is non-compensated.

• • 

  • FSC 10320 Flow Regulator Pressure Compensated Valve

    The valve maintains a constant flow from port 1 to 3, regardless of pressure variations. Flow ranges are dependent upon the diameter of the control orifice. To optimize regulation, the way 2 must have minimum 5 bar of back pressure.

• • 

  • FSC 10321 Priority Flow Regulator Pressure Compensated Valve

    The valve maintains a constant flow at 3, regardless of pressure variations. Flow adjustment at 3 is a hexagonal allen head screw type. Compensator unloading value is equal to 9 bar. To optimize regulation, the way 2 must have minimum 5 bar of back pressure.

• • 

  • FSC 10430 Flow Divider-Combiner

    As a divider the valve diverts input flow (from 2) to 1 and 3 (50:50). Other values can also be setted. With reverse flow, the valve acts as a combiner.

• • 

  • FSC 12320 Flow Regulator Pressure Compensated Valve

    The valve maintains a constant flow from port 1 to 3, regardless of pressure variations. Flow ranges are dependent upon the diameter of the control orifice. To optimize regulation, the way 2 must have a minimum 5 bar of back pressure.

• • 

  • FSC 12321 Priority Flow Regulator Pressure Compensated Valve

    The valve maintains a constant flow from port 1 to 3, regardless of pressure variations. Flow adjustment at 3 is a hexagonal allen head screw type. Unloading value is equal to 9 bar. To optimize regulation, the way 2 must have minimum 5 bar of back pressure.

• • 

  • FSC 12430 Flow Divider-Combiner

    As a divider the valve diverts input flow (from 3) to 2 and 4 (50:50). Other values can also be setted. With reverse flow, the valve acts as a combiner.

• • 

  • GF Series Flow Control Valves

    Series GF valves isolate gauges from damage and inaccurate readings caused by line pressure surges and hydraulic hammer. Series GF features one piece construction and requires no adjustment or maintenance.

• • 

  • GFG2 Series 2-Way Flow Control Valve

    2-way flow control valves series GFG provide pressure compensated flow for a precise movement control. The valve design largely compensates temperature variations to a certain extent. The GFG is optionally equipped with a built-in check valve for the return flow. Series GFG2 features a flow rate independent of pressure and temperature, available for 7 different […]

• • 

  • GT Series Flow Control Valve

    Series GT valves isolate gauges from damage and inaccurate readings caused by line pressure surges and hydraulic hammer. Series GT also features a hardened steel spool, partial snubbing action protects the gauge from surge damage, and has an optional panel mount.

• • 

  • MVI Series Flow Control Valve

    Series MVI cartridge-type needle valves are designed for installation in a precision-machined cavity made in the manifold of the machine and can be used in air, water & oil applications. These valves provide precise metering control and full shutoff of flow. An O-Ring and backup ring installed on the cartridge fully isolate the inlet and […]

• • 

  • PCMS Series Flow Control Valve

    PMCS series valves are used for pressure compensated regulation of the flow. As a consequence of pressure changes, the set value can vary by ± 5 % within the tolerance range. Changes in viscosity and in temperature have the same effect and are to be observed.PMCS series valves are used for pressure compensated regulation of […]

• • 

  • R5P Series Pressure Compensator Valves

    Direct operated 3-way pressure compensators series R5P with SAE flange can be combined with fixed or adjustable flow resistors (throttles) to provide a load compensated flow. Series R5P features a seated type 3-way pressure compensator, SAE 61 flange, 3 sizes, and optional vent function.

• • 

  • SF22A-A2/H 2-Way Flow Regulator, Pressure Compensated

    The SF22A-A2/H is a 2-Way Flow Regulator. •Set flow rate independent of load pressure and temperature changes •Adjusted flow rate depends on the orifice area and adjusted differential pressure •Hardened precision parts •High flow capacity •Quiet and modulated response to load changes •Used in meter-in, meter-out, or bleed-off applications •Wide range of flow rate options […]

• • 

  • SF22A-B2/H 2-Way Flow Regulator, Pressure Compensated

    The SF22A-B2/H is a 2-Way Flow Regulator. •Set flow rate independent of load pressure and temperature changes •Adjusted flow rate depends on the orifice area and adjusted differential pressure •Hardened precision parts •High flow capacity •Quiet and modulated response to load changes •Used in meter-in, meter-out, or bleed-off applications •Wide range of flow rate options […]

• • 

  • SF2C2A-K2/I 2-Way Flow Regulator with Reverse Flow Check

    The SF2C2A-K2/I is a Subplate mounting interface acc. to ISO 4401, DIN 24340 (CETOP 03) •Set flow rate independent of load pressure and temperature changes Adjusted flow rate depends on the orifice area and adjusted differential pressure •Integrated reverse flow check valve •Externally or internally piloted pressure compensator •Hardened precision parts •High flow capacity •Quiet […]

• • 

  • SF32A-B3 3-Way Flow Regulator, Pressure Compensated

    The SF32A-B3 is a 3-Way Flow Regulator. •By-pass flow regulator, set flow rate independent of load pressure and temperature changes •Adjusted flow rate depends on the orifice area and adjusted differential pressure •Hardened precision parts •High flow capacity •Quiet and modulated responsed to load changes •Used in meter-in applications •Wide range of flow rate options […]

• • 

  • SF32A-K3/I 3-Way Flow Regulator, Pressure Compensated

    The SF32A-K3/1 is a 3-Way Flow Regulator. •By-pass flow regulator, set flow rate independent of load pressure and temperature changes •Adjusted flow rate depends on the orifice area and adjusted differential pressure •Hardened precision parts •High flow capacity •Quiet and modulated responsed to load changes •Used in meter-in applications •In the standard version, the valve […]

• • 

  • SFD2F-B4/I Flow Divider – Combiner Valve

    The SFD2F-B4/1 is a Flow Divider-Combinder Valve •Divides pump flow to operate two actuators under different load conditions •Re-combines the return flows to synchronize actuator movement •Division and combination of flows largely independent of the load •Used for synchronisation controls and differential lock •High accuracy under load and pressure imbalance •High flow capacity •Flow variation […]

• • 

  • SFD2F-D4/I Flow Divider – Combiner Valve

    The SFD2F-D4/1 is a Flow Divider-Combinder Valve •Divides pump flow to operate two actuators under different load conditions •Re-combines the return flows to synchronize actuator movement •Division and combination of flows largely independent of the load •Used for synchronisation controls and differential lock •High accuracy under load and pressure imbalance •High flow capacity •Flow variation […]

• • 

  • ZNS Series Flow Control Valves

    Series ZNS sandwich flow control valves controls the actuator movement at overrunning loads. The return flow from the actuator is piloted and controlled by the inlet flow to the actuator, ensuring a cavitation-free lowering of the load. Series ZNS features controlled movement loads, load holding via leak-free poppet valve, and secondary relief protection for the […]